OpUtils

네트워크 모니터링 종합 도구 세트

OpUtils는 네트워크 엔지니어가 IT 자원을 모니터링, 진단 & 트러블슈팅할 수 있도록 도와주는 종합적인 모니터링 도구입니다.
  • 연결된 모든 포트를 찾기 위한 스위치 포트 맵퍼
  • 네트워크에서 사용하는 IP를 추적하는 IP 주소 매니저
  • 권한이 없는 네트워크 접근을 탐지하는 Rogue 탐지
  • 라우터 / 스위치의 구성 파일 백업
 
성공 사례
"Oputils은 네트워크에 관련된 문제를 최종 사용자가 알아차리기 전에 모니터링하는 단일 인터페이스를 제공해 줍니다."
- Jude Croyle, Director - IT, Meet Minneapolis » 더 보기
 
Knowledge Base

This section provides you with the common hiccups that you might encounter with OpUtils along with their possible reasons. Contact Technical Support with the Logs for assistance.

Installation & Startup

  1. I am not able to get OpUtils installed on a Windows Machine. It fails to unpack the jars and the installation quits.
  2. I do not want OpUtils start along with the system. What should I do?
  3. Whenever I start OpUtils, the browser opens to launch the client? Is there a way I can disable this?
  4. After logging into the OpUtils client, clicking any links or tabs from the welcome screen takes me back to the login page. Why?
  5. When I run OpUtils in a Linux machine, I get an error as "Problem while Starting Server !! System halted". What should I do to resolve this?
  6. I am not able to run OpUtils in Windows Vista?
  7. Is it possible to move the installation to a new machine with the configurations and data intact?
  8. Is it possible to use OpUtils to monitor my devices in WAN?

Switch Port Mapper

  1. Switch Port Mapper does not show any MAC Addresses.
  2. Switch Port Mapper displays only the MAC Address and not the IP Address.
  3. I did a 'Switch Port Mapping' using the Switch Port Mapper tools in OpUtils. In the results, I can see several devices connected to a single switch port? How is this possible?
  4. I imported several switches from a CSV file. I get a message that scanning failed for xx switches. What should I do?
  5. I have different router for each VLAN. How can I add to configure it ?
  6. Switch Port Mapper do not show all the ports of the switch?

Bandwidth Monitor

  1. Bandwidth Monitor does not show any utilization information.
  2. The interface speed shown in the Bandwidth Monitor tool is incorrect? Is there a way I can change this manually?
  3. What is the significance of the SNMP version shown while adding an interface? Do I need to change it?

Cisco Tools

  1. In the Config File Manager tool, I am not getting the Startup Config file. It says "Cisco Config Copy MIB" is not supported?
  2. Why do I get the error "E5003: Unable to bind to Port -69" in Config File Manager?
  3. I tried to retrieve a config file from a Cisco device. But, when I click to view the config files, it is blank.
  4. When I try to get the Access Lists, I get an error as "E4002: Wrong CLI authentication parameters". How do I fix this?

Rogue Detection

  1. I am not seeing the data in the Rogue Detection. Why ?
  2. The Rogue Detection tool shows the newly discovered devices, but do not show the Switch details of the discovered device?
  3. I have marked few devices as Rogue. It is not getting rediscovered. Why?

IP Address Manager

  1. When I access the IP Address Manager, it takes a long time to load.
  2. The details like the sysname, location, contact etc., are not available for all the IP Addresses.

SNMP Tools

  1. The Trap Receiver tool does not show any traps?
  2. I do not get the description of the Trap Varbinds in the Trap Receiver tool. Why?
  3. I am not able to GET the values in the MIB Browser; it says "Request Failed or Timed Out. No Error".

Wake on LAN

  1. Wake on LAN does not boot all the machines.

Miscellaneous

  1. What is SNMP Community?
  2. How to install/enable SNMP?
  3. When I use the Send Email option, I get an error: "E6002 : Unable to send mail".
Switch Port & IP Address Management
 
Switch Port Mapper IP Address Manager Rogue Detection Wake On LAN MAC-IP Resolver DHCP Scope Monitor Cisco Config File Manager SNMP Bandwidth Monitor OpUtils Download View Online Demo